High Strength Pneumatic Pipe Beveling Machine For Processing Small
Diameter Pipes
Product Introduction
Beveling tools of BPP inner mounted pipe beveling machines can
bevel different angles under customer requirement. Our tools are
made of high-speed steel and applicable to process all types of
carbon steel. Therefore, our BPP ID mounted pipe beveling machines
are your best choice for processing small-diameter pipes from12.5mm
to 240mm ID. up to a wall thickness of 18mm.
Application
BPP series of pipe beveling machines are widely applied in boiler
plants, pressure vessels, heat exchangers, power plant, nuclear
power, petroleum, chemical engineering, natural gas, pharmacy, pipe
prefabrication plant, pipeline installation engineering,
rush-repair work, etc.
Technical Parameters
Product series
| Model | Processing range
(IDmm) | Wall thickness
(mm) | Rated power
(kw) | Rotating speed
(rpm) |
| BPP1E kit1 | 12.5-15 | ≤3 | 1.43 | 3-70 |
| BPP1E kit2 | 15-20 | ≤5 | 1.43 | 3-70 |
| BPP1E kit3 | 20-28 | ≤6 | 1.43 | 3-70 |
| BPP3E/ BPP3P | 26-79 | ≤15 | 1.43 | 3-70 |
| BPP3PE | 36-90 | ≤15 | 1.43 | 3-50 |
| BPP4E/ BPP4P | 45-105 | ≤20 | 1.43 | 34 |
| BPP6E/ BPP6P | 65-159 | ≤20 | 1.43 | 34 |
| BPP9E | 80-240 | ≤15 | 1.43 | 16 |
*Electric: Rated voltage of 220V, 50/60Hz
Installation & Processing
■ Measure the inside diameters of the pipe to be processed and
choose a suitable machine and expansion block.
■ Select the appropriate block, place it on the bottom of the
expansion block to ensure the top surface of the expansion block
remain horizontal without any inclination, and rotate the sleeve
anticlockwise to tighten the expansion block and, ensure that the
machine is firmly fixed in the pipeline.
■ Choose a tool with suitable angle listed in the tool table based
on the processing requirements, install it on the cutter head of
the machine and tighten the bolts to fix the tools.
■ Rotate the feed hand wheel and extend the feed spindle Loosen
screw and feed.
■ Stretch the machine expansion mechanism into the pipe, and
reserve sufficient feed space between the tool on the cutter head
and the pipe end face.
■ Rotate the expansion sleeve with the ratchet wrench while
adjusting the position of the machine to ensure the feed spindle
and the center of the pipe is concentric; Tighten nuts on the
expansion sleeve with the ratchet wrench after determining the
position.
■ Start the motor. Rotate the feed handwheel to make the cutting
edge contact with the pipe wall, and then bevel.
Safety Instructions
Safety is our priority when pipe beveling machines are designed,
and ergonomics is also taken into consideration to ensure product
safety and reliability.
■ Operators should read the safety instructions carefully before
operation and properly keep them for reference at any time.
■ Operators should be well aware of the products and fully familiar
with the key points of product operations.
■ Please wear suitable working clothes and safety shoes before
operation.
■ Before operation, ensure the operators are kept away from any
live part such as motors and cables.
■ Operators should be kept away from the rotating cutter head as
far as possible for safety when the machine is working.
■ The machines should be used in clean environment and should not
be used in messy circumstances; if it is necessary to be used in
dusty conditions, please wear masks before operation.
■ For electrical pipe beveling machines, please check whether the
voltage of the power supply is correct; for pneumatic pipe beveling
machines please check whether air pressure and flow of the air
source are correct.
